اسٹاک میں ہاٹ پروڈکٹ
HC-HS 2-D7-EBUS
HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert
$35.46امریکی ڈالر
326 اسٹاک میں
اہم وضاحتیں
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
قسم:D7
ٹیسٹ:DIN VDE 0627/86
چوڑائی:21 mm
سپلائر کی معلومات
پروڈکٹس: 0
عام طور پر 2-3 کاروباری دنوں میں بھیج دیا جاتا ہے
کوالٹی کی ضمانت
تیز شپنگ
تکنیکی معاونت
تکنیکی تفصیلات
| پیرامیٹر | قیمت |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| قسم | D7 |
| ٹیسٹ | DIN VDE 0627/86 |
| چوڑائی | 21 mm |
| اونچائی | 34.8 mm |
| لمبائی | 21 mm |
| سلسلہ | HC-HS |
| جنرل | for HC-D7 housing, axial connection 2.0 mm, Allen key |
| درخواست | Power |
| مصنوعات کی قسم | Contact insert with a fixed no. of positions |
| اسمبلی نوٹ | To ensure correct use, installation in housing with IP54 protection or better is required |
| شرح شدہ کرنٹ | 40 A |
| آرٹیکل پر نظر ثانی | 04 |
| رابطہ قطر | 4 mm |
| رابطہ مواد | Copper alloy |
| ہیکساگونل ساکٹ | SW2,0 |
| رابطہ نمبر | 1 - 2 |
| ٹارک کو سخت کرنا | 0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing) |
| کنکشن پروفائل | 2+PE |
| آلودگی کی ڈگری | 3 |
| جہتی ڈرائنگ | |
| عہدوں کی تعداد | 2 |
| شرح شدہ سرج وولٹیج | 6 kV |
| اوور وولٹیج کیٹیگری | III |
| کنکشن ٹیکنالوجی | Axial screw connection |
| رابطہ مواد کی قسم | turned |
| پاور رابطوں کی تعداد | 2 |
| شرح شدہ وولٹیج (III/3) | 400 V |
| کنڈکٹر کراس سیکشن | 4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used) |
| کیریئر مواد سے رابطہ کریں۔ | PC |
| رابطہ سطح مواد | Ag |
| اندراج/نکالنے کے چکر | ≥ 500 |
| کنکشن کراس سیکشن AWG | 10 ... 8 |
| محیطی درجہ حرارت (آپریشن) | -40 °C ... 125 °C (including heating up of contacts) |
| اے سی سی میں کنکشن معیاری کے ساتھ | IEC / EN |
| تعمیراتی اور جانچ کے ضوابط | DIN VDE 0627/86 |
| UL 94 کے مطابق آتش گیر درجہ بندی | V0 |
| انفرادی تار کی سٹرپنگ لمبائی | 8 mm +1 mm |
پروڈکٹ کی وضاحت
Contact insert, number of poles: 2+PE, size: D7, power contacts: 2, Female, Axial screw connection, 400 V, 40 A, 4 mm² ... 10 mm², Application: Power
اہم خصوصیات
- صنعتی معیار
- RoHS کے مطابق
- سی ای سرٹیفائیڈ
- 1 سال کی وارنٹی
پروڈکٹ دستاویزات
ڈیٹا شیٹ
تکنیکی تفصیلات اور کارکردگی کے ڈیٹا
یوزر مینول
انسٹالیشن اور آپریشن گائیڈ
